Destratification fan control
Destratification units or ceiling fans balance the air temperature nearby the ceiling and at the floor level. These fans are often used in large halls with high ceilings to reduce heating costs by preventing large temperature differences between floor and ceiling level. Typical applications are production halls, warehouses, musea, etc. Destratification controllers measure temperatures at ceiling and floor levels to optimise fan speed based on the temperature difference.
Show filters
Hide filters
Filtered result
Destratification controller | dual AC fan outputs 3 A | built-in Wi-Fi
Temperatures at the ceiling and floor level are measured by two temperature sensors with stainless steel probes 85 mm. The higher the difference between both temperatures, the higher the AC fan speed. The combined maximum speed per output is 3 A. There are two regulated outputs available. This destratification controller has a built-in Wi-Fi gateway. The enclosure has an IP54 protection degree against ingress of dust and moisture.
Articles
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Set- for wall mounting of digital temperature sensor, set includes: DTS-MB-BK- 1u, MOZAK-DTS- 1u, MI-DTS-MB-BK- 1u, CGL-M12-BK- 1u, CGN-M12-BK- 1u.
Modbus RTU (RS485) adapter from three RJ45 (8-pins) to 4-pin terminal block.
Multifunctional dual electronic fan speed controller (ACSwitch), Imax: 2 x 3 A, supply voltage: 85-305 VAC / 50-60 Hz, integrated SMPS for external 24 VDC supply (PoM), zero-cross detection, kickstart-softstart function, remote start/stop, TK input, Modbus RTU communication. Internet connectivity with Wi-Fi only.
Current stock 3 U.
Factory lead time 5 Week(s)
Article has been added to your shopping cart.
Destratification control | dual AC fan outputs 3 A | internet gateway
Temperatures at the ceiling and floor level are measured by two temperature sensors with stainless steel probes 85 mm. The higher the difference between both temperatures, the higher the AC fan speed. The combined maximum speed per output is 3 A. There are two regulated outputs available. This destratification controller has a built-in Ethernet/Wi-Fi gateway to connect to SenteraWeb. The enclosure has an IP54 protection degree against ingress of dust and moisture.
Articles
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Set- for wall mounting of digital temperature sensor, set includes: DTS-MB-BK- 1u, MOZAK-DTS- 1u, MI-DTS-MB-BK- 1u, CGL-M12-BK- 1u, CGN-M12-BK- 1u.
Modbus RTU (RS485) adapter from three RJ45 (8-pins) to 4-pin terminal block.
Multifunctional dual electronic fan speed controller (AC Switch), Imax: 2 x 3 A, supply voltage: 85-305 VAC / 50-60 Hz, integrated SMPS for external 24 VDC supply (PoM), zero-cross detection, kickstart-softstart function, remote start/stop, TK input, Modbus RTU communication, integrated Ethernet LAN and Wi-Fi connectivity.
Current stock 3 U.
Factory lead time 5 Week(s)
Article has been added to your shopping cart.
Destratification controller | Dual fan control 3 A
Temperatures at the ceiling and floor level are measured by two temperature sensors with stainless steel probes 85 mm. The higher the difference between both temperatures, the higher the AC fan speed. The combined maximum speed per output is 3 A. There are two regulated outputs available. This destratification controller requires a separate internet gateway to connect the installation to SenteraWeb and to download firmware.
Articles
Multifunctional dual fan electronic speed controller (ACSwitch), Imax: 2 x 3 A, supply voltage: 85-305 VAC / 50-60 Hz, integrated SMPS for external 24 VDC supply (PoM), zero-cross detection, kickstart-softstart function, remote start/stop, TK input, Modbus RTU communication.
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Set- for wall mounting of digital temperature sensor, set includes: DTS-MB-BK- 1u, MOZAK-DTS- 1u, MI-DTS-MB-BK- 1u, CGL-M12-BK- 1u, CGN-M12-BK- 1u.
Modbus RTU (RS485) adapter from three RJ45 (8-pins) to 4-pin terminal block.
Internet Gateway in IP54 plastic enclosure, supply voltage: 24 VDC PoM (Power over Modbus), RTU Modbus communication with master/slave channel, integrated Ethernet LAN and WiFi-connection, version: 2.
Current stock 3 U.
Factory lead time 5 Week(s)
Article has been added to your shopping cart.
Ceiling fan controller | dual AC fan outputs 6 A | Wi-Fi gateway
Temperatures at the ceiling and floor level are measured by two temperature sensors with stainless steel probes 85 mm. The higher the difference between both temperatures, the higher the AC fan speed. The combined maximum speed per output is 6 A. There are two regulated outputs available. This destratification controller has a built-in Wi-Fi gateway. The enclosure has an IP54 protection degree against ingress of dust and moisture.
Articles
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Set- for wall mounting of digital temperature sensor, set includes: DTS-MB-BK- 1u, MOZAK-DTS- 1u, MI-DTS-MB-BK- 1u, CGL-M12-BK- 1u, CGN-M12-BK- 1u.
Modbus RTU (RS485) adapter from three RJ45 (8-pins) to 4-pin terminal block.
Multifunctional dual electronic fan speed controller (ACSwitch), supply voltage: 85-305 VAC / 50-60 Hz, Imax: 2 x 6 A, integrated SMPS for external 24 VDC supply (PoM), zero-cross detection, kickstart-softstart function, remote start/stop, TK input, Modbus RTU communication. Internet connectivity with Wi-Fi only.
Current stock 1 U.
Factory lead time 5 Week(s)
Article has been added to your shopping cart.
Destratification controller | dual fan output 6 A | internet gateway
Temperatures at the ceiling and floor level are measured by two temperature sensors with stainless steel probes 85 mm. The higher the difference between both temperatures, the higher the AC fan speed. The combined maximum speed per output is 6 A. There are two regulated outputs available. This destratification controller has a built-in Ethernet/Wi-Fi gateway to connect to SenteraWeb. The enclosure has an IP54 protection degree against ingress of dust and moisture.
Articles
Set- for wall mounting of digital temperature sensor, set includes: DTS-MB-BK- 1u, MOZAK-DTS- 1u, MI-DTS-MB-BK- 1u, CGL-M12-BK- 1u, CGN-M12-BK- 1u.
Modbus RTU (RS485) adapter from three RJ45 (8-pins) to 4-pin terminal block.
Multifunctional dual electronic fan speed controller (ACSwitch), Imax: 2 x 6 A, supply voltage: 85-305 VAC / 50-60 Hz, integrated SMPS for external 24 VDC supply (PoM), zero-cross detection, kickstart-softstart function, remote start/stop, TK input, Modbus RTU communication, integrated Ethernet LAN and Wi-Fi connectivity.
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Current stock 0 U.
Factory lead time 4 Week(s)
Article has been added to your shopping cart.
Destratification controller | AC fans | 2x 6A | separate WiFi
Temperatures at the ceiling and floor level are measured by two temperature sensors with stainless steel probes 85 mm. The higher the difference between both temperatures, the higher the AC fan speed. The combined maximum speed per output is 6 A. There are two regulated outputs available. This destratification controller requires a separate WiFi gateway (IP54) to monitor data and upload firmware.
Articles
Multifunctional dual electronic fan speed controller (ACSwitch), Imax: 2 x 6 A, supply voltage: 85-305 VAC / 50-60 Hz, integrated SMPS for external 24 VDC supply (PoM), zero-cross detection, kickstart-softstart function, remote start/stop, TK input, Modbus RTU communication.
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Digital temperature sensor for ducts, stainless steel probe (L 85 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Set- for wall mounting of digital temperature sensor, set includes: DTS-MB-BK- 1u, MOZAK-DTS- 1u, MI-DTS-MB-BK- 1u, CGL-M12-BK- 1u, CGN-M12-BK- 1u.
Modbus RTU (RS485) adapter from three RJ45 (8-pins) to 4-pin terminal block.
Internet gateway in IP65 plastic enclosure, supply voltage: 24 VDC PoM (Power over Modbus), RTU Modbus communication, integrated WiFi-connection.
Current stock 1 U.
Factory lead time 5 Week(s)
Article has been added to your shopping cart.
Ceiling fan controller | dual AC fan outputs 3 A | built-in Wi-Fi
Temperatures at the ceiling and floor level are measured by two temperature sensors with stainless steel probes 165 mm. The higher the difference between both temperatures, the higher the AC fan speed. The combined maximum speed per output is 3 A. There are two regulated outputs available. This destratification controller has a built-in Wi-Fi gateway. The enclosure has an IP54 protection degree against ingress of dust and moisture.
Articles
Digital temperature sensor for ducts, stainless steel probe (L 165 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Digital temperature sensor for ducts, stainless steel probe (L 165 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Set- for wall mounting of digital temperature sensor, set includes: DTS-MB-BK- 1u, MOZAK-DTS- 1u, MI-DTS-MB-BK- 1u, CGL-M12-BK- 1u, CGN-M12-BK- 1u.
Modbus RTU (RS485) adapter from three RJ45 (8-pins) to 4-pin terminal block.
Multifunctional dual electronic fan speed controller (ACSwitch), Imax: 2 x 3 A, supply voltage: 85-305 VAC / 50-60 Hz, integrated SMPS for external 24 VDC supply (PoM), zero-cross detection, kickstart-softstart function, remote start/stop, TK input, Modbus RTU communication. Internet connectivity with Wi-Fi only.
Current stock 3 U.
Factory lead time 5 Week(s)
Article has been added to your shopping cart.
Destratification control | dual AC fan outputs 3 A | internet gateway
Temperatures at the ceiling and floor level are measured by two temperature sensors with stainless steel probes 165 mm. The higher the difference between both temperatures, the higher the AC fan speed. The combined maximum speed per output is 3 A. There are two regulated outputs available. This destratification controller has a built-in Ethernet/Wi-Fi gateway to connect to SenteraWeb. The enclosure has an IP54 protection degree against ingress of dust and moisture.
Articles
Digital temperature sensor for ducts, stainless steel probe (L 165 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Digital temperature sensor for ducts, stainless steel probe (L 165 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Set- for wall mounting of digital temperature sensor, set includes: DTS-MB-BK- 1u, MOZAK-DTS- 1u, MI-DTS-MB-BK- 1u, CGL-M12-BK- 1u, CGN-M12-BK- 1u.
Modbus RTU (RS485) adapter from three RJ45 (8-pins) to 4-pin terminal block.
Multifunctional dual electronic fan speed controller (AC Switch), Imax: 2 x 3 A, supply voltage: 85-305 VAC / 50-60 Hz, integrated SMPS for external 24 VDC supply (PoM), zero-cross detection, kickstart-softstart function, remote start/stop, TK input, Modbus RTU communication, integrated Ethernet LAN and Wi-Fi connectivity.
Current stock 3 U.
Factory lead time 5 Week(s)
Article has been added to your shopping cart.
Destratification controller | dual AC fan outputs 6 A | Wi-Fi gateway
Temperatures at the ceiling and floor level are measured by two temperature sensors with stainless steel probes 165 mm. The higher the difference between both temperatures, the higher the AC fan speed. The combined maximum speed per output is 6 A. There are two regulated outputs available. This destratification controller has a built-in Wi-Fi gateway. The enclosure has an IP54 protection degree against ingress of dust and moisture.
Articles
Digital temperature sensor for ducts, stainless steel probe (L 165 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Digital temperature sensor for ducts, stainless steel probe (L 165 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Set- for wall mounting of digital temperature sensor, set includes: DTS-MB-BK- 1u, MOZAK-DTS- 1u, MI-DTS-MB-BK- 1u, CGL-M12-BK- 1u, CGN-M12-BK- 1u.
Modbus RTU (RS485) adapter from three RJ45 (8-pins) to 4-pin terminal block.
Multifunctional dual electronic fan speed controller (ACSwitch), supply voltage: 85-305 VAC / 50-60 Hz, Imax: 2 x 6 A, integrated SMPS for external 24 VDC supply (PoM), zero-cross detection, kickstart-softstart function, remote start/stop, TK input, Modbus RTU communication. Internet connectivity with Wi-Fi only.
Current stock 1 U.
Factory lead time 5 Week(s)
Article has been added to your shopping cart.
Destratification controller | dual fan output 6 A | internet gateway
Temperatures at the ceiling and floor level are measured by two temperature sensors with stainless steel probes 165 mm. The higher the difference between both temperatures, the higher the AC fan speed. The combined maximum speed per output is 6 A. There are two regulated outputs available. This destratification controller has a built-in Ethernet/Wi-Fi gateway to connect to SenteraWeb. The enclosure has an IP54 protection degree against ingress of dust and moisture.
Articles
Digital temperature sensor for ducts, stainless steel probe (L 165 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Digital temperature sensor for ducts, stainless steel probe (L 165 mm). PoM: 24 VDC, Modbus RTU communication via RJ45 connector.
Set- for wall mounting of digital temperature sensor, set includes: DTS-MB-BK- 1u, MOZAK-DTS- 1u, MI-DTS-MB-BK- 1u, CGL-M12-BK- 1u, CGN-M12-BK- 1u.
Modbus RTU (RS485) adapter from three RJ45 (8-pins) to 4-pin terminal block.
Multifunctional dual electronic fan speed controller (ACSwitch), Imax: 2 x 6 A, supply voltage: 85-305 VAC / 50-60 Hz, integrated SMPS for external 24 VDC supply (PoM), zero-cross detection, kickstart-softstart function, remote start/stop, TK input, Modbus RTU communication, integrated Ethernet LAN and Wi-Fi connectivity.
Current stock 0 U.
Factory lead time 5 Week(s)
Article has been added to your shopping cart.